What is the best gauge wire for a trolling motor?

What gauge wire should I use for my trolling motor?

In most cases, the manufactures recommended wire is 8 gauge for most 24-volt systems and 6 gauge for a system of 20 feet or longer. To account for voltage-drop, heat and current changes resulting from low batteries I recommend 6 gauge wire and 4 gauge for over 15 feet.

What gauge wire should I use for a 12 volt trolling motor?

Wire Gauge And Circuit Breaker Size Guide

Cell Amps drawn 10 ft length
12 volt 30 10 awg
12 volt 42 8 awg
12 volt 50 6 awg
24 volt 42 10 awg

What size wire is needed for a 36 volt trolling motor?

Registered. Minnkota 101 or Motorguide 109 – take your pick, both 36v trolling motors, use 2 gauge between the batteries, and no less than 6 gauge from the batteries to trolling motors if you use a trolling motor plug.

IT IS INTERESTING:  Which muscle has the smallest motor unit?

Is 12 or 14 gauge wire better?

12-Gauge Vs 14-Gauge Wire

A larger wire, by virtue of its larger cross-sectional area, generates less resistive heat than a smaller one and can handle more current without overheating. … It’s not quite as flexible as a 14-gauge wire, and it costs a bit more, but it’s always a safe choice on a 15- or 20-amp circuit.

What size battery do I need for a 30 lb thrust trolling motor?

The type and size of battery most suitable for a 30lb thrust trolling motor is a 12 V deep cycle marine battery with at least a 110 amp hour rating, which usually comes under group 27 size battery. The more will be the amp-hour of the battery, the more it will run.

What size battery do I need for a trolling motor?

Most trolling motor batteries fail due to lack of proper charging. We suggest selecting a 12 volt deep cycle marine battery with at least a 110 amp hour rating, usually a group 27 size battery. The higher the amp hour rating, the more run time you will receive.

How many amps does a 50 lb thrust trolling motor use?

As specified above, divide it by 2.4. This means that your battery has 62.5 amp-hours. Suppose you are using an electric trolling motor by Minn Kota 50 pound thrust at a speed setting of 2 and it’s drawing out 20 amps.

How many amps does a 30lb trolling motor pull?

While the Minn Kota Endura C2 30 Freshwater Transom Mounted Trolling Motor (30″ Shaft) model takes 32 amps/hr to get that 30 lbs of thrust, this one can do 30 lbs of thrust for roughly 18 amps/hr.

IT IS INTERESTING:  You asked: What does ODP mean on a motor?

How many amps does a 36 volt trolling motor pull?

A batteries specs always state that there is something like 210 reserve minutes at 25 amps.

Why does my trolling motor plug have 3 wires?

The three wires are for a trolling motor that will operate on either 12 volts or 24 volts. 12/24 volt motors have a switch to choose which you want. Thus the third wire to send power to the 24 volt side of the switch. The red and black wires operate the 12 volt side.

Is 8 gauge wire enough for 36v trolling motor?

Eight gage wire is fine for the length of the original wire. If you can hook the original wire directly to the batteries it will be fine. However, you will be increasing the run if you add more wire, therefore you also have to increase the size to 6 gage.

What kind of battery do I need for a Minn Kota trolling motor?

A Minn Kota trolling motor will operate with any lead acid, deep cycle marine 12-volt battery/batteries. For best results, use a deep cycle, marine battery with at least a 110-ampere hour rating.

How far can you run 12 gauge wire?

You can run a 12 gauge wire up to 70 feet on a 15 amp circuit. That number drops to 50 feet if you run 12 gauge wire on a 20 amp circuit.

Is it OK to mix 12 and 14 gauge wire?

Anyway, the first subject is a bit touchy because it makes it difficult to perform an inspection when all of the wires coming into the panel are 12 but many of the circuits have 14 in them too. There is nothing against code mixing wire size for these circuits as long as the OCPD matches the smallest wire.

IT IS INTERESTING:  What is the difference between platinum and double platinum spark plugs?

How many outlets can you put on a 14 2 wire?

each outlet( receptacle, light) is roughly one amp so you can use 14-2 wire to 12 outlets protected by a 15 amp breaker.