Do I need a trolling motor plug?

A trolling motor plug allows you to safely remove the trolling motor, ensuring you don’t need to worry about connecting wires. They have become an essential accessory because they make your trolling motor’s wiring very easy to manage. Another point about trolling motor plugs is they make great power connection points.

Do all trolling motors have the same plug?

Unfortunately, most trolling motor plugs and receptacles are not compatible with each other as there isn’t a universal plug design.

What do I need to hook up a trolling motor?

What Do I Need To Install A Trolling Motor Plug?

  1. Electric drill.
  2. 1 1/8-inch hole saw drill bit (this is the standard size for a trolling motor plug)
  3. 7/64-inch drill bit.
  4. Electrical wire.
  5. Wire stripper.
  6. Phillips screwdriver.
  7. Trolling Motor Wiring Kit (includes plug, receptacle and hardware)

Can you direct wire a trolling motor?

Ummm… For your specific TM, yes you can do this but not all trolling motors are the same. In the case of many MotorGuide systems the Trolling Motor Is to be unplugged during the charging. Not possible with direct wiring.

IT IS INTERESTING:  How does a direct injection engine work?

How do you wire a trolling motor to a plug?

Feed the wires through the plug housing. On the 12-24V trolling motor plug, connect the positive 24V wire to the terminal marked “24”, the 12V wire to the terminal marked “12” and the negative wire to the terminal marked “-”. On straight 24V trolling motors, connect the two wires to “24” and “-” as appropriate.

Why does my trolling motor plug have 3 wires?

The three wires are for a trolling motor that will operate on either 12 volts or 24 volts. 12/24 volt motors have a switch to choose which you want. Thus the third wire to send power to the 24 volt side of the switch. The red and black wires operate the 12 volt side.

What gauge wire should I use for my trolling motor?

In most cases, the manufactures recommended wire is 8 gauge for most 24-volt systems and 6 gauge for a system of 20 feet or longer. To account for voltage-drop, heat and current changes resulting from low batteries I recommend 6 gauge wire and 4 gauge for over 15 feet.

What size battery do I need for a trolling motor?

Most trolling motor batteries fail due to lack of proper charging. We suggest selecting a 12 volt deep cycle marine battery with at least a 110 amp hour rating, usually a group 27 size battery. The higher the amp hour rating, the more run time you will receive.

What comes with a trolling motor?

A trolling motor is a self-contained unit that includes an electric motor, propeller and controls, and is affixed to an angler’s boat, either at the bow or stern. A gasoline-powered outboard used in trolling, if it is not the vessel’s primary source of propulsion, may also be referred to as a trolling motor.

IT IS INTERESTING:  Can bad gas mess up your spark plugs?

What is the best battery to use for a trolling motor?

10 Best Trolling Motor Batteries Compared

Battery: Type: Reserve:
1. BPS Pro Series AGM X-900 AGM 195 min
2. Odyssey Trolling Thunder AGM 135 min
3. BPS Pro Series Deep Cycle AGM 150 min
4. VMAX Charge Tanks MR-137 AGM 230 min

How do you test a trolling motor plug?

Measure, with a voltmeter – the voltage that is going into the two ends of the wires going to the front of the boat for the trolling motor. You should have 36 volts. Then, go to the trolling motor connector, and measure again. Just put one probe in one connector hole and the other probe in the opposite hole.

Why does my trolling motor wires get hot?

Bad connection or undersized wire will cause excessive heat. … Then, go to your motor wires, and especially your trolling motor plug and connector. It is quite common after a few years that the trolling motor plug or connector or both get corroded, or simply go bad.

Motorization