What is the first thing you should do when troubleshooting a motor?

What are the 7 troubleshooting steps?

The steps are: identify the problem, establish a theory of probable cause, test the theory, establish a plan (including any effects of the plan), implement the plan, verify full system functionality, and—as a final step—document everything.

What should you do first when you arrive to troubleshoot a defective machine?

Electrical Troubleshooting in Seven Steps

  1. Gather information. Gathering information is a logical first step in any troubleshooting endeavor. …
  2. Understand the malfunction. …
  3. Identify which parameters need to be evaluated. …
  4. Identify the source of the problem. …
  5. Correct/repair the component. …
  6. Verify the repair. …
  7. Perform root cause analysis.

1.01.2004

How do you troubleshoot a motor drive?

Measure the motor resistance right at the drive. If the measurement shows an open (high ohm value), the problem is not the drive. Check motor relays, plugs, connectors, conduit boxes, etc. Make sure the motor is receiving a signal: Measure the voltage at the drive’s output terminals.

How do you troubleshoot a motor starter?

Disconnect the motor starter contactor coil and check for a short, ground or open circuit. If a short or ground is found, replace the motor starter contactor coil and start the motor. If the motor start contactor coil is good, with the coil still disconnected, check the control circuit wiring to the contactor coil.

IT IS INTERESTING:  How do you register a motorized kayak?

What are the common troubleshooting problems?

Top 10 Most Common Computer Problems

  1. The Computer Won’t Start. A computer that suddenly shuts off or has difficulty starting up could have a failing power supply. …
  2. The Screen is Blank. …
  3. Abnormally Functioning Operating System or Software. …
  4. Windows Won’t Boot. …
  5. The Screen is Frozen. …
  6. Computer is Slow. …
  7. Strange Noises. …
  8. Slow Internet.

What is the 7 step method?

The 7-Step Method is a reactive problem-solving methodology. Teams apply the method when a correction must be made to the plan based on recurring incidences of one of the five reactive evils.

What are the 6 steps of troubleshooting?

The six steps are:

  1. Identify the problem.
  2. Establish a theory of probable cause.
  3. Test the theory to determine cause.
  4. Establish a plan of action to resolve the problem and implement the solution.
  5. Verify full system functionality and if applicable implement preventative measures.
  6. Document findings, actions, and outcomes.

What are the 8 steps of troubleshooting?

The 8-Step Process is:

  1. Step 1 – Clarify the Problem (framing) (GTS1-2) …
  2. Step 2 – Breakdown the Problem (GTS 2) …
  3. Step 3 – Target Setting (GTS2) …
  4. Step 4 – Root Cause Analysis (GTS3) …
  5. Step 5 – Develop Countermeasures (GTS3) …
  6. Step 6 – See Countermeasures Through (GTS3) …
  7. Step 7 – Monitor Process and Results (GTS3)

10.03.2020

What are the basic steps of troubleshooting?

9.2 General Steps to Troubleshoot an Issue

  1. Identify the symptom: Identify the Type of Issue. Find the problem area. …
  2. Eliminate non-issues: Make sure the correct patches, drivers, and operating systems are installed. …
  3. Find the cause: Check for typical causes in the area. …
  4. Find the fix: Find a possible workaround.
IT IS INTERESTING:  How do I know if my 2001 Cummins is a high output?

What causes an electric motor to stop working?

Stressful mechanical, environmental, and electrical operating conditions can all cause electric motor failure. Electrical failures are winding failures caused by an open contactor, bad connection, blown fuse, excessive heat, electrical overload, or broken power lines.

How do I know if my VFD is bad?

Take the negative multimeter lead and put it on the – terminal of the VFD. Take the positive multimeter lead and put it on each input and output terminal of the VFD one at a time. If a terminal is good, it should return with a OL (open) reading on the meter.

How do you diagnose a bad electric motor?

You should test the windings for a “short to ground” in the circuit and open or shorts in the windings. To test your motor for short to ground, you’ll need to set the multimeter to ohms and disconnect the motor from its power source. Then inspect each wire and look for infinite readings.

How do you troubleshoot a motor overload?

Check the motor starter contactor, the fuses, and the overload relay. 4) Rectify the root cause of overload and reset the overloads by push the reset button. Start the motor and check the running motor amps and compare to rated FLA and overload heater size using a clamp-on ammeter.

Motorization